Errori - Allarmi Elettrodomestici
Faq - Errori - Allarmi Elettrodomestici Lavatrici, Lavastoviglie, Frigoriferi, Asciugatrici e Forni
Ricerca Errori - Allarmi Elettrodomestici Lavatrici, Lavastoviglie, Frigoriferi, Asciugatrici e Forni
Contatti Errori - Allarmi Elettrodomestici
Lavatrici Errori - Allarmi di tutte le marche !
Washing Machines Errors Alarms - All Brands ! AEG, ARISTON, CANDY, DAEWOO, ELECTROLUX, HOOVER, LG, MIELE, REX, SAMSUNG, WHIRLPOOL ....
Errors - Alarms Appliances
Faq - Errors - Alarms Home Appliances Washing machines, Dishwashers, Refrigerators, Ovens and Dryers
Ricerca Errori - Allarmi Elettrodomestici Lavatrici, Lavastoviglie, Frigoriferi, Asciugatrici e Forni
Contact - Errors Alarms Home Appliances


Assistenza Elettrodomestici Milano
Assistenza Elettrodomestici Monza
Assistenza Elettrodomestici Bergamo
Assistenza Elettrodomestici Brescia
Assistenza Elettrodomestici Multimarche
Assistenza Elettrodomestici Varese

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Errori - Allarmi Elettrodomestici - Lavatrici, Lavastoviglie, Frigoriferi, Asciugatrici e Forni

We use cookies to improve your browsing. By visiting the site you agree to our use of cookies. More information about cookies

Error Alarms Appliances

The most common errors:


 

F05 - The washing machine does not drain

                         ( Ariston - Washer )

F06 - the engine doesn't spin

                         ( Whirlpool - Washer )

F21 - Washer does not drain

                         ( Bosch - washing machines )

E50 - Do not turn the basket

                         ( Rex - Dryer )

5E - Error non-discharge

                         ( Samsung - Washer )

E05: Faulty sensor NTC

                         ( Candy - Washer )

EH3 voltage too low

                         (AEG)

F08 circuit resistance interrupted

                         ( Whirlpool - Washer )

Choose The appliance

AEG

ARISTON

AMANA

BOSCH

CANDY

DAEWOO

Electrolux

HOOVER

INDESIT

IGNIS

LG

MIELE

REX

SAMSUNG

SIEMENS

SMEG

Whirlpool

ZANUSSI

ZEROWATT

ZOPPAS

GORENJE

COMFEE
  • Washer Errors

Error Codes AEG Lavamat

E11

Lack of water for washing machine

tap water, filter (screen) clean

Electronics / valve / connection cable / switch / replace luchtval

E13

Too little water in the washing machine

Check valve, supply hose and the hose properly explain (bend pipe), clean the filter.

Valve / feed tube / pressure switch replaced / hydraulic control circuit.

error code

E20


E21

No drainage from washing machine

Filter verify the presence of foreign bodies, exhaust control, tube, blocking the tube.

Pump / pressure switch / pressure sensor / electronics replaced

E23

Pump / problem of electronic washing machine

Machine supplier bubbles

Pump / electric / pneumatic pump replaced cables

E24

Measuring circuit

Contact your provider

Replace electronics

Error Codes

E30


E31

Problem pressure washer

Contact your provider

Pressure sensors / flat cable replaced

E32

Pressure sensor gives a message

Tap water, the filter control for the objects.

Valve / luchtval / pressure sensor replaced

E33

Pressure sensor problem

Contact your provider

Pressure switch / pressure sensor / tape / cable luchtval / heating / electronic replaced

E34

Pressure sensor problem

Contact your provider

Pressure sensor / tape / cable replacement luchtval

E35

Message security in the washing machine

Contact your provider

Pressure switch / pressure sensor / tape / cable luchtval / electronic / replace hydraulic control.

E36

Problem of measuring circuit

Contact your provider

Replace electronics

E37

Problem of measuring circuit

Contact your provider

Replace electronics

E38

Pressure switch problem

Contact your provider

Luchtval cleaning / replacement

E39

Pressure switch problem

Contact your provider

Replace electronics

E3A

Relay heater problem

Contact your provider

Replace electronics

error

E40


E41

Open the cover, malfunction of the machine closing.

Control block, failure: dealer called

Lock / link / cable replacement electronics

E42

Balance defective, opened during the washing / not open to the final wash.

Contact your provider

Lock / link / cable replacement electronics

E43

Triac (power circuit) for closing the machine fault

Contact your provider

Lock / link / cable replacement electronics

E44

Measurement circuit closing

Contact your provider

Replace electronics

E45

Measurement circuit closing

Contact your provider

Replace electronics

error

E50


E51

motor triac (power circuit) circuit

Contact your provider

Electronics / flat cable replaced

E52

Engine fault block / speedometer (meters rotation) interruption / motor ribbon cable defective.

Contact your provider

RPM / engine / tire / electronically replaced

E53

Measuring circuit of the motor

Contact your provider

Replace electronics

E54

Engine fault relay

Contact your provider

Replace electronics

E55

Motor circuit is interrupted

Contact your provider

Replacement engine / control flat cable

E56

Referral tachometer (meters rotation)

Contact your provider

Tachometer replaced

E57

Higher total current of 15A

Contact your provider

Engine / motor / electronic ribbon cable replaced

E58

The flow of an upper phase of 4.5 A

Contact your provider

Engine / link / cable parts of the engine electronics

E59

no tachometer signal (meters of rotation) to the motor

Contact your provider

RPM / engine / tire / electronically replaced

E5A

heat sink temperature exceeds 88 degrees

Contact your provider

Electronic engine control module

E5B

Voltage less than 175 volts

Contact your provider

Electronic Engine / flat cable replaced

E5c

Voltage higher than 430 Volts

Contact your provider

Electronic engine control module

E5D

Data transmission problem

Contact your provider

flat cable replaced

E5E

Electronic communication of engine failure

Contact your provider

Replace electronics

E5F

Electronic engine failure

Contact your provider

Electronics / motor / electronic ribbon cable replaced

error code

E60


E61

Do not heat, heating or NTC defective.

Contact your provider

NTC / heating / flat cable replaced

E62

Overheating temperature greater than 88 degrees

Contact your provider

NTC / heating / flat cable replaced

E66

Heating relay defective.

Contact your provider

Protection against dry running half dry run protection / link / electronic parts

E68

Flow diversion excessive

Contact your provider

Heater or other internal parts

E69

Do not heat, voltage> 5Volt

Contact your provider

Heater / flat cable replaced

error code

E70


E71

NTC (temperature sensor) is defective.

Contact your provider

NTC / tape / electronic cable replaced

E74

NTC is not the place

Contact your provider

Mounting position NTC control

error

E80


E82

Errata reste-position switches

Contact your provider

Replace electronics

E83

Read switch error

Contact your provider

Misconfiguration, replace electronics

E84

Circulation pump of the measuring circuit

Contact your provider

Replace electronics

E85

Failure of the circulation pump

Contact your provider

Circulation pump / electronics replaced

error

E90


E91

Error electronic communications

Contact your provider

I / electronic / belt / electronically replaced

E92

Inequality in electronics

Contact your provider

E / A in the form of electronic head electronics

E93

Misconfiguration

Contact your provider

Replace electronics

E94

Incorrect configuration of washing

Contact your provider

Replace electronics

E95

Communication error

Contact your provider

Replace electronics

E96

no consensus version of the hardware configuration

Contact your provider

Replace electronics

E97

no coherent program and switch configuration

Contact your provider

Replace electronics

E98

disagreement engine electronics and other electronic devices

Contact your provider

Electronics / flat cable replaced

E99

in- / uitgave electronic speaker problem

Contact your provider

Speaker / flat cable replaced

E9a

Speaker firmware problem.

Contact your provider

Import / electronic editing replaced

E9F

communication error between the engine electronics and other electronic devices

Contact your provider

Electronics / flat cable replaced

error code

EA0


EA1

DSP failure

Contact your provider

DSP / tire cord / belt / electronic replaced

EA2

DSP signals failure

Contact your provider

Replace electronics

EA3

DSP engine pulley can not block.

Contact your provider

DSP / ribbon cable / electronics / belt replaced.

EA4

DPS defect

Contact your provider

DSP / electronic / flat cable replaced

EA5

Triac DSP failure

Contact your provider

Replace electronics

EA6

Drum blocked in 3 to 30 seconds

Contact your provider

Substitution DSP, replacing the belt, the drum lid has been opened.

error code

IB0


EB1

Frequency outside limits

Mains supply voltage wrong / crowds. If correct: call provider

Replace electronics

EB2

Mains voltage too high

Mains voltage socket faulty / degraded. If correct: call provider

Replace electronics

EB3

Mains voltage too low

Mains voltage socket faulty / degraded. If correct: call provider

Replace electronics

EBE

Defective safety relay control panel

Contact your provider

Replace electronics

EBF

Control circuit of the cycle of the safety relay is defective.

Contact your provider

Replace electronics

error

EC0


EC0

Valve locks

Contact your provider

Valve / electronic / flat cable replaced

EC2

Dirt level of sensor malfunction

Contact your provider

Sensor replaced

error

EF0


(EFO)


see the top of this page!


EF1

Nothing screen clogged, blocked afvoerdam

Lint Screen / afvoerdam cleaning

-

EF2

Overdose of foam during pumping, lint screen clogged, blocked afvoerdam

Do not overdose Lint / cleaning afvoerdam

-

EF3

Aqua Control System mobilized / ribbon cable faulty pump / failure

Contact your provider

Loss in the appliance repair / replace cable / pump.

EF4

No signal of the flow sensor

encourage water / water control.

Flow sensor block lifted.

EF5

Centrifugation is interrupted, imbalance greater than 1200 grams

A large loads clock / placement of machine vibration and possible corrections.

-

error code

EH0


EH1

Frequency outside the limit

Contact your provider

Valve / electronic / flat cable replaced

EH2

Mains voltage too high

Mains voltage socket faulty / degraded. If correct: call provider

Replace electronics

EH3

Mains voltage too low

Mains voltage socket faulty / degraded. If correct: call provider

Replace electronics

EHE

Defective safety relay panel steering wheel

Mains voltage socket faulty / degraded. If correct: call provider

Replace electronics

EHF

Control circuit of the cycle of the safety relay is defective.

Contact your provider

Replace electronics

Errors washing machines ariston

F01 - There is a short circuit at the triac engine.

F02 - Jam engine tachometer. Do not turn the engine

F03 - resistance thermometer interrupted / short circuit.

F04 - Pressure switch jammed on empty.

F05 - Pressure switch jammed on full.

F07 - relay heater not working.

F08 - heater relay is not activated.

F09 - Errors in programming setup (setup).

F10 - The pressure does not perceive correctly the water level.

F11 - Can not activate the pump.

F12 - Communication error with the card.

F13 - resistance thermometer interrupted, short circuit.

F14 - Heating element defective.

F15 - relay faulty heating.

F17 - No interlock.

F18 - Communication error with the card.

H20 - Defect filling: check inlet hose, filters and valves of water entry.

F01 - Porthole load not properly closed


F02 - Tap not open


F04 - Foreign bodies blocking the drain pump


E23 - Water Leaks


E17 - pocca pressure water inlet


E18 - Drain blocked


F21 - Exhaust blocked


D01 - Cock closed


D02 - Clogged filter


D07 - Door not closed


E3 - Properly close the portholes


E5 - Fully open the water tap


E6 - Drain pump blocked


E2 - Engine failure

e01


Locking safety door defective

Check that the door is closed properly

Check the wiring of the locking device

Check lock

Check the braking device of the basket, if present


e02


The machine does not fill with water

Check pressure of the hydraulic network

Check the inlet hose

Check the filter input (at the entrance of the inlet hose behind the car)

Check solenoid water inlet

Pressure switch broken

Wiring fault


e03


The washing machine does not empty

Check that the filter is not blocked or obstructed

Check that the exhaust pipe is clear of any blockage or obstruction

Check the wiring of the drain pump

Check that the drain pump is not defective

Check the pressure switch

Check the wiring of the pressure switch


e04


The machine is too full of water

Check the functionality of the pressure switch

Check the wiring of the pressure switch

Solenoid water inlet blocked to "open"



e05


NTC fault (sensor temperature): open circuit or shorted

Check the wiring of the temperature sensor

Check the correct operation of the sensor


e06


Error EEPROM (electronic controller)

Check the wiring

Check the electronic control board


e07


Engine failure

Check the motor terminal

Check the wiring

Check the motor brushes (no motors with inverters)

Check the connections of the tachometer

Check for proper operation of the engine



e08


Failure of the engine tachometer (speed sensor): open circuit or shorted

Check the motor terminal

Check the wiring

Check the connections of the tachometer

Check for proper operation of the engine


e09


Failure of the engine tachometer (speed sensor): open circuit or shorted

Check the motor terminal

Check the wiring

Check the connections of the tachometer

Check for proper operation of the engine


e12


Communication error on the control board or sensor circuit interrupted air heating (only washer dryer)

Check the wiring of the control board

Check for proper operation of the sensor heating air




e13


Communication error between cards and cabling (only washer dryer)

Check the wiring between the control cards

Check the electronic control modules



14


Error heating water

Check the wiring of the thermostat and resistance

Check the functionality of the resistance

Check the NTC (temperature sensor)



e15


Error programming the control board

Turn off the device. Wait 10-15 seconds and try to run the program again

Reprogram the electronic control unit

Replace the electronic controller



e16


Failure to properly isolate electrical components (short circuit)

Check the presence of defects in electrical insulation

Check resistance heating water

Check the wiring resistance



e17


Faulty signal from the engine tachometer (RPM)

Check the motor terminal

Check the motor wiring

Check the connections of the tachometer

Check for proper operation of the engine



e18


Error by the control module - anomaly electrical frequency input

Check the wiring board

Check the electrical frequency input

Check the power supply network

IE - Error WATER INLET


The tap is closed. Turn on the tap.

The valve inlet filter is clogged. Clean the filter valve.

The water level sensor (pressure sensor) is an inferior product Changing the water level sensor

or broken. (Pressure sensor).



OE - Error = DRAIN ERROR


The drain hose is bent or clogged. Clean and straighten the drain hose.

The drain pump. Replace the drain pump.


EU = Error ERROR IMBALANCE


The washing is concentrated to a side of the drum during rotation. Rearrange the laundry.



THE DOOR OPEN ERROR =


The Start / Standby button is pressed while the door is open. Close the door.

The door lock switch is a product of inferior quality. Change the door lock switch.

The bracket of PCB does not control the door lock. Change the roll holder PCB.



E2 = overflow error


The water is fed continuously because of an input of the lower valve. Changing the valve.

The inlet valve is normal, but the water level sensor Changing the water level sensor

(Pressure sensor) is less. (Pressure sensor).

The dose of the engine exhaust does not operate. (The engine exhaust is an inferior product or broken.) Replace the engine exhaust.



E4 = ERROR ESCAPE

Cause and solution = water leakage from the tank or from the exhaust pipe. Control the loss of the tank or of the exhaust pipe. Then change the bath or the exhaust pipe.



E5 - Error HIGH VOLTAGE


Linen is blocked between the gasket and the drum. Rearrange the laundry.



E6 - EMG ERROR


Linen is blocked between the gasket and the drum. Rearrange the laundry.

The engine is an inferior product. Replace motor.



E7 = direction error


The motor rotates in an opposite direction. Change the [censored] PCB or engine.

The IC engine room is an inferior product or broken. Replace the engine room or the IC engine.



E8 = MOTOR ERROR


The engine is not normally connected. Check the motor connector.

The engine is not working. (The engine is an inferior product or broken.) Replace the engine.



E9 = sensor error PRESSURE


The water level sensor is an inferior product. Change the water level sensor.



H2 - ERROR THERMISTOR WASH


Washing thermistor is an inferior product or broken. Change the wash thermistor.

The washing thermistor is not connected normally. Check connector washing thermistor.



H4 = WASH ERROR THERMISTOR OVERHEATING


The heater worked without the water in the tub. Check the water level.

Washing thermistor is an inferior product or broken. Change the wash thermistor.



H5 = ERROR TEMP WATER


The water temp. It is above 45 ° C in the course delicate and wool. (Washing thermistor is an inferior product or broken.) Change the wash thermistor.




H6 - ERROR HEATER WASH


The dose of washing heater is not working. (The temperature of the water. Do not rise above 2 ° C for 15 minutes.) Change the heater.




H8 = WASH ERROR HEATER OVERHEATING


The heater worked without the water in the tub. Check the water level and the heater.




PFE = ERROR PUMP FILTER


The filter of the drain pump is blocked. Clean the filter of the drain pump.

The drain pump is not working during rotation. Changing the pump exhaust.

The large amount of detergent has been used. Use the correct amount of detergent.

The exhaust pipe is positioned higher than 1 m above the floor. Place the 1m exhaust pipe under the floor

Err or error


- Indicates a choice inaccurate performed by the user, for example the selection of an option not provided for a given washing.



188 or 888


- May appear briefly when the washing machine as a result of the combined ignition lights on the display.



C1, E10 or 1 beep


- It indicates that there is no flow of water or that it is very low, therefore insufficient for the proper functioning of the washing machine



C2, E20 or 2 beeps


- Indicates a problem with the drain



C3, F3, EF3 or 3 beeps


- Indicates the presence of water on the bottom of the washing machine or a problem of water discharge



C9, E50 or 9 beeps


- May indicate an imbalance in the spin cycle or an overload of work, due to its continued use - engine failure



Cd, E40 or 4 beeps


- Indicates that there is a problem the door is closed



CE


- Indicates a defect in the detergent drawer.



CF or E90


- Indicates a fault with the electronics



E80 or 8 beeps


- The program selector went wrong, then return to the "0" and set up a program.



IB0, EH0 or 11 beeps


- Indicates a problem on the power supply, a lack of energy



EF0, EF1, EF2 or 15 beeps


-can indicate the fluff filter clogged, that there is water on the bottom of the tank or has created too much foam



EF0, EF3 or 15 sounds


- May indicate a loss of water

e01


Locking safety door defective

Check that the door is closed properly

Check the wiring of the locking device

Check lock

Check the braking device of the basket, if present


e02


The machine does not fill with water

Check pressure of the hydraulic network

Check the inlet hose

Check the filter input (at the entrance of the inlet hose behind the car)

Check solenoid water inlet

Pressure switch broken

Wiring fault


e03


The washing machine does not empty

Check that the filter is not blocked or obstructed

Check that the exhaust pipe is clear of any blockage or obstruction

Check the wiring of the drain pump

Check that the drain pump is not defective

Check the pressure switch

Check the wiring of the pressure switch


e04


The machine is too full of water

Check the functionality of the pressure switch

Check the wiring of the pressure switch

Solenoid water inlet blocked to "open"



e05


NTC fault (sensor temperature): open circuit or shorted

Check the wiring of the temperature sensor

Check the correct operation of the sensor


e06


Error EEPROM (electronic controller)

Check the wiring

Check the electronic control board


e07


Engine failure

Check the motor terminal

Check the wiring

Check the motor brushes (no motors with inverters)

Check the connections of the tachometer

Check for proper operation of the engine



e08


Failure of the engine tachometer (speed sensor): open circuit or shorted

Check the motor terminal

Check the wiring

Check the connections of the tachometer

Check for proper operation of the engine


e09


Failure of the engine tachometer (speed sensor): open circuit or shorted

Check the motor terminal

Check the wiring

Check the connections of the tachometer

Check for proper operation of the engine


e12


Communication error on the control board or sensor circuit interrupted air heating (only washer dryer)

Check the wiring of the control board

Check for proper operation of the sensor heating air




e13


Communication error between cards and cabling (only washer dryer)

Check the wiring between the control cards

Check the electronic control modules



14


Error heating water

Check the wiring of the thermostat and resistance

Check the functionality of the resistance

Check the NTC (temperature sensor)



e15


Error programming the control board

Turn off the device. Wait 10-15 seconds and try to run the program again

Reprogram the electronic control unit

Replace the electronic controller



e16


Failure to properly isolate electrical components (short circuit)

Check the presence of defects in electrical insulation

Check resistance heating water

Check the wiring resistance



e17


Faulty signal from the engine tachometer (RPM)

Check the motor terminal

Check the motor wiring

Check the connections of the tachometer

Check for proper operation of the engine



e18


Error by the control module - anomaly electrical frequency input

Check the wiring board

Check the electrical frequency input

Check the power supply network

The interpretation of the error codes can be done by the sum of the values ​​corresponding to the flashing lights.

The image below shows three flashing lights. This is the front of the control panel or greater Indesit. The values ​​for each indicator are 1, 2 and 8. The sum of these values ​​gives 11. In both cases, the error code 11: Drain pump problem.


01


 failure: the engine Triac in short. The electronic component that controls the motor is shorted



02


 No rotation of the motor



03


 Temperature sensor failure


04


 the water level too high



05


 Drain Fault. The machine does not empty or does not see the level of vacuum



06


 Information nonexistent program selector


07


 error resistance


08


 insufficient water control



09


 Memory problem on the power board. The EEPROM (electronically) is in default or scheduled.



10


 problem of controlling the water level



11


 drain pump failure



12


 The exchange of information between cards



13


 cleaning and drying. Sensor drying



14


drying resistance



15


 cleaning and drying. Drying permanent heating



16


 only Washer top. drum positioning system on the pulley.



17:


 faulty lock



18


 Issuance of electronic communication. power and replace card EEPROM.

Errori Lavatrici Indesit
Errori Lavatrici Indesit

ERROR "IE" - input error water does not enter or does not reach the level established


ERROR "OE" - the water does not drain completely


ERROR "EU" - error of balance


ERROR "dE" - open door error


ERROR "tE" - error Water Heating


ERROR "FE" - error of water overload


ERROR "PE" - error pressure


ERROR "LE" - error of motor overload


ERROR "PF" - a power failure

- "F41" and the program stops


Electronics failure



- Waterproof


It took the anti-flooding system Miele.



- Failure influx water and the unit does not spin


For security reasons it is not possible to spin before the first operation.

With the block of centrifugal programmed from production, it prevents a centrifugal device before there is an influx of water.



- The remaining time you change or stop


The washing machine has an electronic control with automatic quantity that calculates the amount of laundry introduced into the drum and adjusts the washing time. How it works: At the beginning is made to flow a set amount of water, determined by the selected program. After a short time, the electronics control the water level to check how much water has been absorbed linen. On the basis of this data it is made to flow more water or not. The machine uses this technique to calculate the amount of laundry introduced. If the load is complete, the electronics automatically reduce the duration of the washing and rinsing and may decide to skip a rinse. Or it can decide to extend the duration of the rinse and add an additional rinse, if such has been dosed too much detergent or too much foam is formed.



- The display shows the call to call for service


The light bulb that illuminates the inside of the basket is not in the right position.



- No signal on the display


The display turns off automatically to save energy ('standby').



- The display shows streaks


The contrast of the display is not set correctly for the light.



- 'Load <25%' if the washing machine is empty


When the washing machine is empty it appears always this message.



- The display shows the exhortation to remove the transport safety when they have already been removed


It was not carried out the first operation (first washing) or the electronics has been reset (after a power failure, after turning off the machine or after pulling the plug).



- Failure affllusso and a triangle with an exclamation mark


The flow is blocked or compromised.



- Message that invites you to enter the pin code


Focus is on the pin code.



- 'Anti-crease controls dosage'


It is too much foam formed during washing.



- Fault in the exhaust system and see a triangle with an exclamation mark


The final end of the drain hose is too high.



- The display streaks or white spots


When cleaning the display with a cloth to dust, it may happen that the display is charged with static electricity. For this reason, on the top or bottom edge of the display could be generated striped or white points



- The 'LED Start' does not light


The door was not locked properly.

Err or error


- Indicates a choice inaccurate performed by the user, for example the selection of an option not provided for a given washing.



188 or 888


- May appear briefly when the washing machine as a result of the combined ignition lights on the display.



C1, E10 or 1 beep


- It indicates that there is no flow of water or that it is very low, therefore insufficient for the proper functioning of the washing machine



C2, E20 or 2 beeps


- Indicates a problem with the drain



C3, F3, EF3 or 3 beeps


- Indicates the presence of water on the bottom of the washing machine or a problem of water discharge



C9, E50 or 9 beeps


- May indicate an imbalance in the spin cycle or an overload of work, due to its continued use - engine failure



Cd, E40 or 4 beeps


- Indicates that there is a problem the door is closed



CE


- Indicates a defect in the detergent drawer.



CF or E90


- Indicates a fault with the electronics



E80 or 8 beeps


- The program selector went wrong, then return to the "0" and set up a program.



IB0, EH0 or 11 beeps


- Indicates a problem on the power supply, a lack of energy



EF0, EF1, EF2 or 15 beeps


-can indicate the fluff filter clogged, that there is water on the bottom of the tank or has created too much foam



EF0, EF3 or 15 sounds


- May indicate a loss of water

Models Big Wash:

4E - occurs when water is not charged, inside the washing machine, up to the level established by the program within 5 minutes. Make sure that the tap water inlet is open. Check the water pressure.

5E - Error non-discharge. You may clear the problem by cleaning the drain filter.

EU - occurs when the load is not 'balanced oe' tangled. The problem ricolve dissolving any entanglement of the leaders and rilavviare program.


Pura +:

4E - occurs when water is not charged, inside the washing machine, up to the level established by the program within 5 minutes. Make sure that the tap water inlet is open. Check the water pressure.

5E - Error non-discharge. You may clear the problem by cleaning the drain filter.

EU - occurs when the load is not 'balanced oe' tangled. The problem ricolve dissolving any entanglement of the leaders and restarting the program.


SLIM:

4E - occurs when water is not charged, inside the washing machine, up to the level established by the program within 5 minutes. Make sure that the tap water inlet is open. Check the water pressure.

5E - Error non-discharge. You may clear the problem by cleaning the drain filter.

EU - occurs when the load is not 'balanced oe' tangled. The problem is solved by dissolving any entanglement of the leaders and restarting the program

F01 - Porthole load not properly closed


F02 - Tap not open


F04 - Foreign bodies blocking the drain pump


E23 - Water Leaks


E17 - pocca pressure water inlet


E18 - Drain blocked


F21 - Exhaust blocked


D01 - Cock closed


D02 - Clogged filter


D07 - Door not closed


E3 - Properly close the portholes


E5 - Fully open the water tap


E6 - Drain pump blocked


E2 - Engine failure

E1

Loss of water detected by the safety device water


E2

Detected anti-spill equipment failure


E4

Heating water sensor error detected



E5

Washing machine has detected no load



E6

The machine failed to drain the water



E10

Motor overcurrent



E11

Motor triac short error



E12

Detected engine tachometer error



E13

Error blocking port detected


E14

Dryer heating sensor error detected



E-

Programmer main flaw card

FH or AH: Do not fill with water


 FP: Do not discharge water


 FA Code: problem with the Aquastop. The leak detection system located on the base of the device is activated.


 F05: Problem on the probe. Check the water temperature sensor (approximately 12 kilo-ohms at 20 ° C, 3.2 to 60 ° C), and the connector (sensor and map).


 F06: Problem tachometer. Control the rotation of the motor.


 The fault code F07: Failure of the control board of the engine.


 F08: Failure of the heating circuit. Check resistance and connections.


 F09: recognition of risk of overflow device.


 F10: Temperature too high on the engine


 Fault F12: heater in an insulation fault (mass) or power relay resistance permanently bonded (PCB).


 F13: Fault water distribution micromotor contact positioning.


 F14: problem in the memory (EEPROM) device.


 F15: Failure of the motor (parasites).


 F21: communication error between the display board and the power board.


 F22:. F21 same


 F24: overflow


 F32: Overheating of the motor plate


 F35: Failure analog switch - pressure


 F39: Card Error relay power.


 F42: Failure of the control board of the engine.


 F61: communication error between the control board and the motor plate.


 F62: error steam circuit of the temperature sensor.


 F63: Failure to produce steam.


 F64: Failure of solenoid steam.


 F70 error: Communication error with the power board and display.


 F71 Fault:. F70 same


 F73: error in the memory of the display module.


 Fod: Overdose detergent. Try different rinsing / unloading device.


FDU failure Code: failure to unlock the door.


FdL Code: failure to close the door. Fdu checkpoints. General, to delete a default value, you may want to disconnect a few minutes, then turn it back on.

E1X: Problem filling.


e2x: Problem exhaust.


E3X: Problem filling.


E4X: Problem closing of the door.


E5x: Problem rotation of the motor.


E6x: heating problem.


E7X: Problem temperature sensor.


E8x: Problem selector programs, or problems at the water recirculation pump


E9X: configuration problem of the electronic board. . Reconfigure or replace PCB


EAX: positioning system defective drum.


EBX: power problem.


EFX: Indicates operating errors. Overdose detergent, drain clogged filter imbalance (poor positioning of the machine), the valve is closed.

E01: problem with the door lock.


 E02: the water level is not reached


 E03: water drain


 E04: Water level too high


 E05: Temperature sensor defective.


 E06: problem with the electronic programming.


 E07: malfunction. motor brushes


 E08: Problem rotating drum. Failure to inform the tachometer signal. Check connections, wiring and magnet tachometer.


 E09: Triac Motor Control in default.


 E10: problem reading data from the program selector.


 E11: drying module defective (only washer dryer).


 E12, E13 and E14: the lack of communication between video card and power board.

Err or error


- Indicates a choice inaccurate performed by the user, for example the selection of an option not provided for a given washing.



188 or 888


- May appear briefly when the washing machine as a result of the combined ignition lights on the display.



C1, E10 or 1 beep


- It indicates that there is no flow of water or that it is very low, therefore insufficient for the proper functioning of the washing machine



C2, E20 or 2 beeps


- Indicates a problem with the drain



C3, F3, EF3 or 3 beeps


- Indicates the presence of water on the bottom of the washing machine or a problem of water discharge



C9, E50 or 9 beeps


- May indicate an imbalance in the spin cycle or an overload of work, due to its continued use - engine failure



Cd, E40 or 4 beeps


- Indicates that there is a problem the door is closed



CE


- Indicates a defect in the detergent drawer.



CF or E90


- Indicates a fault with the electronics



E80 or 8 beeps


- The program selector went wrong, then return to the "0" and set up a program.



IB0, EH0 or 11 beeps


- Indicates a problem on the power supply, a lack of energy



EF0, EF1, EF2 or 15 beeps


-can indicate the fluff filter clogged, that there is water on the bottom of the tank or has created too much foam



EF0, EF3 or 15 sounds


- May indicate a loss of water

F1

Washing machine temperature sensor failure

The washing machine has detected a problem with the temperature sensor of heating water and, although the program will complement the car does not heat the water.


Check the wiring of the temperature sensor or thermistor

Check thermistor or temperature sensor

If defective Replace thermistor

Check heater

Check the wiring to the control module or timer


F2


Lock detected fault

The lock on the door of the washing machine has been detected as defective or failed to engage properly.


Check that the door has been closed properly

Check the wiring to lock

Check lock

Check the wiring to the control module or timer


F3


Dry the water load

The machine failed to reach the level

The water level has not been recognized as achieving the right level by the pressure sensor.


Check the tap is turned on and that there is sufficient water pressure available

Check the wiring of the intake valve water and electrical connections

Check the pressure sensor wiring and electrical connections

Water inlet valve

Check the water level or the pressure sensor

Check the connections to the main control module or timer


F4


Inverter card can not control the engine

The card module to the inverter, the motor speed and the voltage of the electronic control can not control the speed of the motor. Please note that this code will be displayed only on models that have a brushless motor mounted.


Check connections and wiring between the inverter board and motor

Check dynamo engine is complete and in place

Check the Main Control Board

Replace the card drive if the fault is not found on the engine


F5


 control board of the machine and a card inverter can not communicate

The main control module can not communicate with the control board of the motor speed or tab inverter.


Normally when this error is reported the fault will be found in connection with the inverter board, and not the control module, which correctly report the error.


Check the wiring between the main control board and the inverter board

Check the blocks of connectors on both cards

Replace the inverter board


F6


Washing resistance detected faulty

A fault has been detected in the heating circuit water which normally means that the heater washing is open circuit.


Check wiring and connections to the heating water

Check heating element for continuity

Check the thermostat or thermistor wiring and connections

Check thermostat or thermistor

Check the connections on the main control module


F7


The washing machine is able to drain the water and will stop with water in it.


Drain the washing machine manually before proceeding with the diagnostics.


Check the filter pump for obstructions or foreign objects

Check exhaust pipe of exhaust for each block or obstruction

Check the drain pump for the continuity

Rotor Control discharge pump is good

Check wiring to the pump and connections for the discharge pump

Check the connection to the main control module


F8


Engine trouble Washing detected

A fault has been detected with the main motor of the washing machine, even if it is no specific indication of the nature.


Check all connections to the main engine

Engine control unit tachometer

Check motor brushes if they are used

Check motor armature

Check the connections to the main control module


F9


Leak detected on models mounted washing machine with Aquastop

This error code is used on only Gorenje washing machine models that have their Aquastop leak detection system installed and will not display on models that do not have this feature.


Check for leaks and fix

Check supply pipe Aquastop

Check the connections to supply pipe Aquastop

Check connections float leak-detection device if present

Check the connections to main control module

E10 - Do not fill with water


E11 - Earned level overflow


E12 - overflow protection


E20 - Drain pump


E21 - Do not Download


E30 - Do not close the door lock


E31 - Do not open the door lock


E32 - The porthole opened during operation


E33 - Pressure switch faulty


E34 - Temperature sensor defective


E35 - temp defective


E36 - NTC broken


E40 - Eprom error


E50 - Voltage too high


E60 - Broken engine


E61 - Do not turn the engine


E62 - RPM - defective


E70 - Button control locked

E01 - The light of the numbers 1 and 2 will flash.


 - The door has not been closed properly



E02 - The light of the numbers 1 and 3 flashes.


 - The level of water in the washing machine is below heater. The pressure of the water supply is low or missing altogether.



E03 - The light of the numbers 1 and 4 flashes.


 - The pump has failed or the pump filter is obstructed or drain pump is in open circuit.



E04 - The light of the numbers 2:03 will flash.


 - There is an excessive amount of water in the washing machine.



E05 - The light of the numbers 2:04 will flash.


 - The heater is defective or the heat sensor has failed.



E06 - The light of the numbers 3:04 will flash.


 - The motor is broken.



E07 - The light of the numbers 1, 2 and 3 flashes.


 - The electronic card is faulty.



E08 - The light of the numbers 2, 3 and 4 flash.


 - The motor is broken



E09 - The light of the numbers 1, 2 and 4lampeggia.


 - The mains voltage is too high or too low



E10 - The light of the numbers 1, 3 and 4 flash.


 - Communication error

All Brands

Whirlpool washing machine does not turn on ?

If the washing machine on and off during washing or simply would not light up, only these components are likely to be replaced !

Rex Dryer does not turn on ?

The Rex dryer would not light up ?

You can repair the card!

Do not need to replace it !

Copyright © 2012-2014 Errori-elettrodomestici.it . All rights reserved. By Stefano

Do you need assistance ?

Milano Monza Bergamo Brescia Cremona Varese